Hunter H

are they neo magnets? cause for the size i've never seen a magnet as strong as them before

I've got an iphone 3g running iOS 3.1.3 and it's supposedly been unlocked, but when I put my t-mobile simcard in it just says searching for network for 5-6 minutes and then shows no signal, pleas help

If I'm going to get some aftermarket 17x9 rims for my truck would 35x12.50x17's be too wide for my rims?

I recently got a SCT SF3 programmer for my truck(2001 ford f-250 5.4 gas) and have an aftermarket exhaust on the way, I was thinking about getting a bigger throttle body and a K&N cold air kit, would I get a noticeable difference over what I've already done to the truck?

I've got a 2001 ford F-250, and want to put an electric fan on it, but I'm not sure if the fans I'm looking at move enough air to keep my truck cool. the fans I'm looking at are Derale part no. 16914 and are advertised at 1100 CFM each, and I plan on installing 2, Would this be enough CFM to keep my truck cool?

I've got a 2001 ford f-250 and I found a guy selling a set of ranch hand full replacements that were on a 2004 and just want to know if they'll fit

I've got a 2001 ford f-250 5.4 gas v8 truck and was going down the street to go to the store today and it just died in the middle of the street, i tried starting it and nothing, went under the hood and it wason't getting any fuel, i checked the pump and its coming on when i turn the key on so i replaced the filter, and it's still got the same problem, any suggestions as to what's going on with my truck?

I'm installing an air horn on my truck later this week and have the horn itself picked out and have a tank, i'm just trying to decide on a compressor, I've got a Viair 280c in mind but I'm not sure if it's big enough, my tank is about 3.25 gallons and will only need filling once a day from 90 to 110 PSI. would the 280c be big enough to do this?

I'm going to put a total of 6 off road lights on my truck and would like them to be on the same switch an was just wondering if i had the amperage draw correct. Each light is rated at 100 watts, totaling 600 watts, if the truck is running on 13.5 volts would the amp draw be about 44.5?

I've got a '91 mastercraft with an indmar 454 in it that threw a rod, will a short block out of a chevy or gmc truck work or is there a difference in the bottom end of the engine?

i recently got a 2001 ford f-250 super duty with a 5.4 gas engine and it's definatly an upgrade from my old one but it just doesn't have enough power, i want to get a tuner but can't decide which to get i'm torn between the superchips cortex, the hypertech max energy and th diablosport predator, does anyone have any particular one they would suggest over the other two?

I was going to go with an e303 camshaft, ford aluminium gt-40 heads, edelbrock 1406 carb, bbk shortie headers, offroad x-pipe and flowmaster 40 series mufflers with turndowns, now I'm going with the same carb and exhaust but am considering an edelbrock 2091 top-end kit instead of the e303 and gt-40 heads, would i be able to expect similar hp numbers out of this set up as opposed to the e303 and gt-40s?

24 hours of Le Mans is on tomorrow and I want to record it on my DVR, but don't have enough space to record all of it, does anyone know of an adapter that goes from a male eSATA to a female USB?

I've got a 94 extended cab F-150 4x4 with an e4od transmission and a 5.8l v8, will it be able to pull a boat trailer that weight a little over 5,000 pounds to the lake?

Does anyone know how to take th governor off of an e4od transmission?

I've got a 92 mastercraft maristar 240 with an indmar marine 454 in it and went to start it today and the solenoid clicked then did nothing, it's still drawing off the battery because i notice a voltage drop when i bump the key, does anybody know what advance auto parts or oreilly auto part no. that would replace the starter that's on there?

I got my Fi BTL recone in the mail today, and it came with the sub, basket, new terminals but didn't come with a gasket, how bad can it be to run the thing without a gasket for a few days? until the new one comes in?

I'm going to be building a new box for my sub this weekend and want to know how close i can have the end of my port to the wall of my box before i have to put a bend in it?

I've got a 1994 Ford F-150 with a 5.8l engine and i want to do a custom cold air setup but because the stock engine has a dual venturi throttle body on it i'd have to buy twice the piping and 2 filters and i don't want to do that. if my truck was mass air it'd have a "Y" pipe to go from the 2 venturies on the throttle body to one pipe that goes to the mass air sensor and then on to the stock air box. I found that part that the seller on ebay says came off a 6 cylinder truck and wanted to know if that'd be the same part. if it helps here's a link to the listing

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?Vi...

I'm considering purchasing a Fluke Meter model 113 it's listed on the sears webstie as a "True RMS utility mlutimeter" now does this mean that it'll somehow indicate when it's getting a clipped signal?