DeAnthony T

Social Security sent my fiancee a "letter statement" for me and her to sign stating that we present ourselves to the public as married(which we do not do). Her son is intellectually disabled. They are saying that my income will effect him although he is not my child. I am trying to find out any information I can because the customer service person we talked to seemed to tell us because the state (aka food stamps and title 20) give benefits based upon who is in the household then so do they. As if it wasn't definitive until I guess you "present yourself married to the public." Any useful information would be very helpful. Thank you in advance.

Hi,

I have a 2004 Hyundai Santa fe 6 cylinder with, I think, Is a catalytic converter issue.There seems to be a power issue....I step on the gas and the car goes barely 30mph. This is the kind of converter that has the manifold and converter in one piece. I dropped the pipe behind the front (closest to radiator) converter and it immediately restores power. My question is do you think its the converter if my power returned after I dropped the pipe and if so how would I go about removing the 7 screws where the manifold bolts into the engine? It looks very difficult and I haven't been able to find any good DIY's online. Also if the converter was collapsed how would dropping the pipe restore power if I dropped exhaust AFTER the converter. Please help if you can, Thanks.

Hi,

I have a 2006 hyundai santa fe 2.7 liter engine. I replaced the ignition coil packs (3) due to a engine misfire from cylinder 1 and 4. I no longer have a CEL but the engine has no power in idle or when driven and cuts off when I press gas half way. After the truck stalls the first time it is really hard to start back up. It normally takes 5-8 tries to get it running and that is with me mashing the gas pedal. The truck does have occasional starting issues when temperatures are below 30 degrees and not sure if that is related to the issue or not? When I cannot get the engine to run, I use starting fluid in which it starts up fine but still lacks power. The rpm will not go above 2000 without idling back down and stalling out completely. Could plugs and wires cause this issue? Again I have no CEL on.

Also I disconnected the MAF sensor to be sure it wasn't the culprit yet it still runs the same. Has anyone had an issue like this? Thank you in advance for your time and help.

I have AGP motherboard installed in my desktop. It has an AMD Duron 1.8GHz processor onboard. I am running the 32-bit version of Windows 7 and have 640MB of ram installed. I am having a problem getting the computer to recognize the graphics card. I install the card into the PCI slot and plug in the VGA and I get a bunch of random screen flashes and colors. When I unplug the VGA and put it back into the board WITHOUT taking out the graphics card, the computer acts as if the monitor isn't connected at all(amber light on Dell monitor). As soon I pull the GeForce card out it boots up like normal. Any ideas/help would be greatly appreciated. I am running the AWARD Bios as well.....Thanks in advance.

It was deleted unintentionally.

Is there a site or something i can go on to look him up? Any help would be greatly welcomed. Thanks

I have a 2000 grand am and a little over a wk or so ago, my low coolant light came on and my heat started to become cooler than normal. I checked the coolant level in the reservoir and it was empty. I refilled with fresh coolant but light remained on. Every two days or so after that the coolant level goes down to completion and i end up having to refill it again. Any ideas or help will be greatly appreciated. Oh and i felt around the water pump but there doesn't seem to be any leaks in or around it. I haven't been able to check out the thermostat as of yet...help please.

My laptop has not been booting up correctly at all...could my hard drive be the problem since the BIOS hard disk check failed??

I have a HUGE problem...I have a Compaq F700 that wont let me do ANYTHING!!! It is running Vista, Ive tried going into safe mode to get into my control panel but all it says is "This application has failed to start because urlmon.dll was not found. Re-installing the application may fix this problem." After i hit ok it say "Class not registered", I myself have no idea what this means. Every program i try to get into says something along the same lines as that. I am running out of ideas, and am very frustrated at this point. Any help will be greatly appreciated!! Oh yea, 4 some reason or another all of my restore points are gone as well....

I have a 95 toyota tercel and the oil pressure sending unit broke off at the threads in the block...Sigh.....Ive tried a tap set but i still cant get it to budge! What other options do i have to get that outta there? Does anyone also know about how much a shop will charge to remove? Thanks In Advance!

i was in a minor car accident but my drivers side airbag deployed. i need to know how to replace...and i already have replacement airbag. thanks in advance

there was a commercial for a mans body spray that had women chasing him.....what was that anybody?