Houston

Does anyone know of a good lender (trustworthy) enough to get around a $10,000 loan to consolidate debt and only have to make one payment a month instead of like 6. Thanks alot and anything will help.

So my wife signed the 3 copies of the dissolution of marriage papers. Now i have to pay $350 for the court fees and stuff. Does she still have to be served in order for this divorce to go through and start. And if i do not know where to find her how do i go about getting this divorce finalized? I'm in califonia and there is a 6 month and 1 day wait for the finalization. Does anyone know anything about this. Pretty much should i pay the $350 to file or what? any help would be great!

My amp hook ups look like this ++ -- (positive,positive negative,negative) next to each other. how do i hook up my 12" single voice coil 4 ohm sub to make 4 ohms to the amp. do i go to the outside +/- or the inside +/-

I have a kenwood 12" subwoofer, 4 ohms, 1000W max peak, 300W RMS. What would be the best amp (specs and all) to match up with my subwoofer where i will get the best sound and the amp won't overheat or shut off and on from protecting. What recommendations do you guys have? I'm looking to only spend a couple hundred bucks for the amp, and the box i have my sub in is ported.

I got a speeding ticket last month for doing 65 in a 55. I have a lifted truck so my speedometer shows i'm going 55 but am really going 65 or faster. If i get it calibrated will i get out of this speeding ticket? And about how much will it cost?

I can barely hear music coming out of the speakers on the passenger side of my car. The driver side speakers are great and even when i put the balance all the way to the right it stays the same. What could be causing this. If i put my ear up to the speakers i can hear the music but they just don't get loud.

I want to run my two subs in series so my amp doesn't get as hot and i lower my ohms on it. I have a 12" SVC(single voice) and a 10" DVC(dual voice). I have a 1000W amp, the 12" sub has a 1000W max and the 10" sub has a 600W max. The amp is two channels, what is the best way to go about this. I'm thinking i can't run them in series but maybe someone knows different. Thanks

My check engine light comes on and stays on for about 2 days, then shuts off for about a day. Could this be a bad gas cap, i had to replace it awhile ago and it's one where it doesn't click on but just turns onto it.

I have a 1000W amp, 1 12" kenwood 1000w max, and 1 10" 600W max. It bumps but my amp shuts off and on after awhile from overheating. Probably shouldn't of gone with a boss amp to begin with but.... so if i run thicker wire to both subs will it make a difference in sound quality and/or overheating? Thanks

I can barely hear anything coming out of my speakers on the passenger side of my truck. The driver side sounds fine. I have to put my ear up to the speakers on the passenger side to hear anything. You can hear the music but it is extremely low, even when putting the balance all the way to that side and turning the volume up it stays the same. Any ideas

I have a 12" 1000W max sub and a 10" 600W max sub. Both Dual Voice. Should i hook both of them up dual voiced and use two channels? The amp is a 1000W 4ohms and both subs are 4 ohms. So should i go single or dual voice from the subs to the amp

I just put some new tweeters in my truck. One side sounds great but the other has constant distortion, then shuts off, then sounds great for a couple minutes then does the cycle over again. I have thicker wire connecting the tweeters to the speakers, should i be using the same size wire as the tweeters or what else could it be. It is also not as loud as the other one.

I just bought a 1000W Boss amp. I'm hooking up a 600W sub and a 1000W sub, one to each channel. I'm wondering what Mode to use. The amp has Low Pass (45-90Hz), Full Range, and High Pass (50-500Hz). Also the input sensitivity switch gives me the choice of 100mV or 2-8v. If anyone can explain what would be best for the amp and sound it would be greatly appreciated. Thanks

I have a 1000W boss amp and a 1000W kenwood sub 4 ohms. I also want to hook up a 600W max 4 ohm 10" sub, but i want to bridge the 1000W sub to the amp so i get max power out of it, and hook up the 600W to one channel to draw 500W to it. Is that a good idea or should i just hook both up to one channel each, getting 500W per speaker.

My #5 fuse in my 2001 Ford F-150 only blows when i put it in reverse. The #5 is connected to my reverse lights, a/c clutch, and cruise control. How do i find out why it is only blowing in reverse.

I am about to buy an amp for a kenwood, the amp puts out 200w RMS and the kenwood is rated 200W RMS. Should i get an amp that puts out a little less RMS than the max the sub calls for.

I'm being charged by a company called NCO Financial group, i've heard many people saying they are a scam but either way it is on my credit report. What is a DV and what do i do about fighting this

I have an 800w peak 4 ohm amp, i have two 4 ohm speakers. I have a two channel amp so do i bridge them (explain how) or put them in parrallel (explain how) as to not fry my amp or screw up my subs. Thanks

I have a 12" kenwood RMS max 150 Peak 1000W. And a 600W peak 150RMS 10" . My 800 watt amp is 4 ohms and both speakers are 4 ohm. what do i need to do to make sure they are all wired correctly

i have two subwoofers that have RMS max at 150 at 4 ohms. I have to make sure the amp is on 4 ohms so i don't get a higher rms output to the speakers. how do i make 4 ohms come out of the amp to the speakers?