mark

crutch field sent me it and said it might need it but the harness adapter didnt have a black ground and just had positive and negative leads for each speaker so i just crimp capped everything and it all works good but im still a lil worried cause when i replaced the door speakers they had black and green wire which green wire means its grounded to the chassis and that means i need the adapter but i dunno.

so long story short i was trying to haul wood in a sorty muddy spot, in low at high rpms i saw black smoke come from it as if it was a diesel i thought at first it was the belt but im still not sure. im using 91 octane fuel and the four wheelers old and the old stock ignition system which was known to go out very quickly which four wheelers at 6k miles and around 900hours and it does mis out here and there. just kinda wanna know if its possible to roll coal on a gas engine.

i have a battery that not long ago quit working so i put distilled water in it and then it worked fine, now ever since the cap has leaked battery acid and got it every where all over the four wheelers axle turning everything grey and causing some bolts to rust. Where should i Start to getting rid of the corrosion.

i have old golfcart battery that are going out they can hold a charge but the hightest volts they go is 12v with 2 of them they cant power a trolling motor very well its weak so if i gets another which maybe they would charge to 16 volts. would that damage a 30lb thrust 12v motor.

if so any suggestions on good cheap amp for maybe a 150 watt constant sub and 4 speakers.

i would like to use these what should i do could buying a mixer from Walmart work? i dont really feel like taking this to a professional.

my atvs battery keeps going dead over time while driving it. the battery dies quicker if the fan comes on the battery we are using is a 40 dollar ever start from walmart. the battery that was suggested for it was around 120 dollars and the everstart was the closest thing to it. i got a voltage meter and while it was off it was around 12.1volts and on it was 12volts dead even

im thinking no, but some dude off ebay bought my processor i was selling and is claiming he has 20 years of computer knowledge and that it is defective. He said it posts in bios but fails any other task. when i sent this it had alot of bubble wrap and had no issues the maybe six months it was used. It was bought new and was a locked processor so it never even would of got hot.

ok so i have about a 10 year old set of jvc sub and speakers the sub wont produce sound i hooked up a ohm meter and it says 4 ohms i also hooked up another sub (that i know isnt broken) and it made no noise either hopefully this is a easy fix but i doubt it

i have it set to 83x on processor cache ratio and stress testing and such it runs fine i have the cpu clocked at 5.1ghz @1.4 volts

I reinstalled windows on another drive but none of the game will work because they were under drive letter c:

i want to reinstall windows but i cant backup the hard drive cause games don't work so i'm just gonna install windows on another hard drive and keep everything on it reinstalling windows is a must have i have changed motherboards 2 times and my i5 7600k barely performs at par when oc'd to 5ghz

i wanna try to reinstall windows because i have changed mobo ram and cpu. but every time i try and backup my main hard drive so i can get the game its only backs up like 180 gigs and the hard drive has 450 gbs of game and stuff on it gta v wont run none of the game will run on the hard drive when i back it up

i have tried to use system restore but it just says failed to restore it every time. i ve tried to use the boot diagnostic but it just reboot and pretends nothing happened. the only thing that had been changed on the computer was a 500 ssd was installed and drivers were installed for it. and yes i have the hard drive selected with the os on it

ive been looking at the ASUS® VP228H 21.5" LED-LCD Gaming Monitor, Black because its 1 ms response time im currently using a tv and its hard to read words on screen sometimes cause i think its not full 1080p it has a 8ms response time which is pretty good for its age and that its a tv. and why is it on high demanding games the refresh rate gets even higher like gta? in the first menu i can easily tell there is a massive delay

Specs 1060 6gb i5 7600k with 8gb 2400mhz. if i play gta 5 after pc has been on for a while it will stutter like crazy and not get much fps if i restart it it will get around 60-80 fps for about 4 hours then gets slow again. i think it might be norton some people told me to not use it

the mobo is a b250m-ds3h and i have 8gb sof drr4 2400mhz ram but when i play games like gta 5, i get 60 fps with optimal settings but the drops are insane it would probably have a 40 fps average. i do have the worst performing 1060 (Asus 1060 6gb turbo but that shouldn't matter. and this is on 1080p maybe very high settings with most forms of aa off or on low

I have read places to torque them to 30 and wait 30 minutes and then torques to 60-64 then else where it says to torque to 35+ what should I do? also what should I torque the rockers to as well?