Eddie

My 2004 Mazda 6 V6, 5 speed, tachometer will not move from zero at low rpms. It will move only at the point of when it needs to be shifted. After that it drops back to zero.  Changed cam and crank sensors.  Communication issue with crank sensor is only code pulled, reason changing, but still exist. Could this be an electrical issue or issue with computer?  Slight hesitation when at idle and pressing accelerator. No noticeable issues when driving other tha

Ok this seems strange. I have a 2004 Mazda 6, V6, Manual transmission. I dont see a check engine light come on when I turn on the ignition. Looking closely at the cluster, I still dont see any indication that there's one.

On a 2004 Mazda 6, 3.0l engine, what side is considered the front/rear , left/right. I know cylinders 1-3 is on firewall and 4-6 etc..

I have a 2004 Mazda 6, 3.0L, 5 speed manual. Car runs great and no issues starting. No CEL on. When I scan I'm getting a P0340 code.. The rpm gauge only reading when above 2000rpm.

What so you all think, timing issue..

I have an 2004 Trailblazer Ext. Recently been experiencing lose of battery power or either slow start as if battery is am drained. Mostly experience it after driven and it sat for an hour or so up to I'm leaving working. It doesn't happens every time.

The clock will be set back to 12:00 and I get a slow turn over but it does start up. Battery is under 5 years old, but not ruled out. Or maybe the ignition switch.

I have a 2004 Mazda 6, V6. The blower / ac fan stays on high whenever the engine is on. I'm unable to turn it off by the ac control, of which I have switched out with no results. All other controls work except turning the fan off or to a lower speed. Any help is appreciated.

I have a 2004 Mazda 6, 3.0L. There is a P0340 code stored, but I am unable clear it. There is no CEL on nor any other warning light.. Any clues on why. Car runs fine. No noticeable issues other than RMP gauge only moves around 2.5k rpms.

I have a 2004 Mazda 6, 3.0L. I have no headlights, or blinkers. When I turn the light on all rear lights come on except the turn signal/blinkers. The front side markers also comes on. The blinkers on dark blinks faster than normal. I've looked at all fuses and relays.

Everything works as it should except the headlights and blinkers. Any help would be greatly appreciated...

I have a 2004 Mazda 6, 3.0L. I have no headlights, taillights, or hazards. When I switch from high to low the dash light shows it. Also turning on headlights the dashboard dims indicating the lights are on but they are not. The turn signal flashes quickly on dash but the actual lights dont. Any ideas? All dash lights works btw.

Just curious and looking for a fix. Why some of the late model Cadillacs just suddenly stop working. No crank no start and no power. 2003 CTS with a 3.2 engine and an 2002 Deville with the Northstar engine. Have anyone gotten one back running after experiencing those symptoms.

I have an "02 Cadillac Deville with around 107k. My traction control light stays on but there are no abs codes in the DTC. If I run the car s self diagnostics and press to clear codes the light goes out and stays out until I turn the car off and restart it.

But no codes are there. Could this be an ecu issue needing to be reprogrammed/flashed. And is this something only a dealer can do.

Thanks in advance

I have an 02 Caddy Seville with around 108k. My traction control light stays on when I start the car. There are no DTC codes relating to the abs. Only have a RIM code and code relati f to the air vents: B0429, B0409. Any idea on what to check. I read so.e posts about this and the third brake light was the culprit. Thanks in advance.

I have a 2002 Caddy Deville and pulled an abs module from a junk yard car same make and model. I then had it rebuilt and installed it. Works fine but my traction control light now stays on. There are no DTC codes.

Took to dealer to have it flashed they telling me things I already know about it being the wrong module. Isn t the the purpose of the reprogramming is to fix that missing link between the module Ann computer. Them quoted me a $1900 job. I was like take my car off the racks and I ll pick it up. Even with a new module it would need to be reprogrammed is what I said to them, so what s the difference. Well it may not work was their reply.

Don t mind buying a new module but it won t be the $700 one from them.

I have a 2002 Deville. My traction control light comes on when I start the car. There are no DTC codes present which is kind of strange. I changed the control module and even had one refurbished with the same results.

If I press the clear codes for the ABS the light goes out and stays out until I turn the car off and start it back up.

Any suggestions would be greatly appreciated..

I have a 2002 Cadillac Deville. Water is leaking down the passenger side corner in the floor running down the seam from the back wall under the glove box. Where should I look to track it from the outside? It's near where the wires comes through the firewall under the glove box but I can't find where it is coming from. Thanks.

2002 cadillac deville, when it rains rear passenger side floorboard gets wet. This don t happen when running the ac. I ve checked the sunroof drain lines and they re all clear. Seen some posts about a drain plug on the firewall but I can t seem to fine it. I ve looked in the crowl and didn t see any type of debris. Thanks in advance for the help.

Recently I noticed that after coming out first gear my truck wasn't shifting. The rpms rev up higher than normal for the speed if the truck. It still picks up speed but it won't shift. Sounds like it's straining but will not shift. I got up to over 65mph letting up off the accelerator every now and then but it still won't shift.

This is the I6 type engine 4x4 LS model. No service

Lights on or anything. I doubt a code scanner would be any help. Hopefully something that don't requires a rebuild.

Any info would be helpful and appreciated.

My car recently threw this code while also illuminating the abs & traction control light. I know the code means the abs module stalled. Being that the brake light did not come on would saying the module is not bad a good bet. I haven't erased the code nor reset anything you. Hopefully that's the right move. Or maybe removing and reinstall the abs module will do the trick. Any advice. I find remove the abs fuse though. And the brake light came on then . So hopefully resetting it will work.

Ok here's the situation. Just bought a new battery fir my truck. The otg error day on my way to work the battery light blinks on and off every so often and the voltage gauge dropped from around closer to 14 to about the first large mark after 9, I guess that's like 10.5. Being that I have a brand new battery I continued my 22 mile trip to work.

Truck started with no problem after work but voltage gauge was still done below normal. And battery light blinking every so often. About a half mile before getting home the voltage gauge goes back to near 14 and no blinking battery light. Even after putting a laid on the battery with the a/c and headlights on.

Any clues other than getting it tested which would be my first step.