Yahoo Answers is shutting down on May 4th, 2021 (Eastern Time) and beginning April 20th, 2021 (Eastern Time) the Yahoo Answers website will be in read-only mode. There will be no changes to other Yahoo properties or services, or your Yahoo account. You can find more information about the Yahoo Answers shutdown and how to download your data on this help page.
Trending News
6 Answers
- Anonymous6 years agoFavorite Answer
A hole in vinyl siding opens a door for moisture and insects to intrude. Fortunately, you can repair most small holes and punctures without a professional's help. You’ll need a tube of color-matched vinyl siding caulk, which you can purchase from siding retailers. Caulk is matched the same way as paint. If the retailer doesn’t have information for your siding on file, take in a small piece of siding to ensure a good match. If the hole is larger than a nail or screw puncture, you’ll also need a scrap of matching siding to use as a patch.
Sponsored Link
Asian Paints
Concerned About What Colour To Choose? Let Our Experts Help You!
asianpaints.com/ColourConsultancy
Fill a Puncture
1
Clean the siding around the hole with vinyl siding cleaner or mild dish detergent and water and a soft sponge. Wipe the siding dry with a rag.
2
Cut the nozzle tip on a tube of color-matched vinyl siding caulk with a utility knife and fit the caulk into a caulk gun. Cutting the tip at a slight angle gives you more control over application. Prime the caulk tube by squeezing the trigger two or three times, then release the trigger.
Click Here!
3
Align the caulk tube's nozzle opening over the hole in the siding.
4
Squeeze the caulk gun’s trigger to fill the space behind the hole with caulk. This step is important for a long-lasting repair. Squeeze as much caulk through the hole as you can, then slowly lift the nozzle and release the trigger. Overfill the hole slightly, ending with excess caulk outside the hole.
5
Scrape a plastic card or semi-rigid rubber caulk trimmer lightly across the hole to remove most of the excess caulk. Alternatively, let the caulk harden and then trim off the excess with a utility knife blade.
Patch a Hole or Tear
1
Clean the siding around the hole with vinyl siding cleaner or dish detergent and water, then dry the siding.
2
Cut a scrap piece of siding to a length that is several inches longer than the hole. A clean way to cut vinyl siding is to score it with a utility knife and then bend the vinyl at the score. It should snap apart. You can also use utility shears.
3
Cut off the uppermost edge of the scrap, which has a series of holes for siding nails, with a utility knife. Don’t cut off the whole curved or lipped edge across the top edge of the siding; only cut off the nail hole strip.
4
Trim off the bottom edge the same way that you trimmed the top, leaving the curved lip. After trimming, you should have a flat section of siding with a curved top and bottom edge.
5
Press the patch over the damaged section of siding. The curve at the top and bottom of the patch should fit over the same curves on the damaged section of siding. If the patch won’t fit over the damaged section, trim off the curved edges to make a flat patch.
6
Open a tube of color-matched vinyl siding caulk and fit it into a caulk gun. Squeeze the gun's trigger a few times to start the flow.
7
Remove the patch from the wall, and apply a generous amount of color-matched vinyl siding repair caulk on the back of the patch. Don’t worry about using too much, as you can clean up excess caulk after the patch is installed.
8
Apply a contiguous bead or line of caulk around the hole in the siding.
9
Set the patch over the damaged siding. Apply pressure to help the pieces stick together, if necessary. Let the sealant dry for as long as the manufacturer recommends, then apply more caulk around the perimeter of the patch, if desired. If you trimmed off the curves and mounted a flat patch, apply painter’s tape across the patch to hold it against the siding until the caulk dries.
- Nandan_MallickLv 66 years ago
Find out how to repair damaged vinyl siding on your home, from small holes to large cracks. ... Since it may be hard to match existing siding, it's a good idea to ask the installer for a few ... Any suggestions/advice is greatly appreciated. ... Past Episodes of Today's Homeowner | Remodeling Contractor in Mobile, Alabama (AL) ...
- elhighLv 76 years ago
Pop the damaged siding pieces off and replace with new.
Then be careful how you aim the mower in the future. Thrown rocks from lawn mowers and weedeaters are the main cause of holes in vinyl siding.
- How do you think about the answers? You can sign in to vote the answer.