Westsail43

They are making tunnels in the logs leaving a hole almost 1/4 inch big, I have seen no sign on my live trees but was wondering if I should be worried

Then after I turn it on again it shuts down even sooner until I let it cool down and it goes back an hour after shutting down again ... so on and so fourth. What might the issue be and the cheapest way to fix it, Is it the Power Supply? the YSUS I feel I can switch these out no problem but do not know where to start,

Thanks for any and all help...

and progressively got worst to the point it now it only stays on for minute then when it is warmed up only for a second or two before it shuts off. I would like to know what it is that causes this? The power supply, the YSUS or the main board.

What steps can I take to narrow it down? Thanks for any and all help and information.

Tad

tadsmalley@gmail.com

I bought an old italian made welder (Daytona 180) that is only 110 volts. I can use .35 flux wire with the welder doing 1/4 to 3/8 plate and angle getting good penetration but a lot of spatter. I am wanting to change to Argon and CO2 mix and use the largest wire I can but do not know what the machine can handle? .030? .035? or even .045? I have read a lot of bad things about the Daytona welding machines but I got this one for 100 bucks and so far its been great.

Thanks for any and all information

Welding Newbie

I have a 2008 oil pan that a quick lube employee stripped the plug on, I have the car jacked up out side and have removed all the nuts and bolts and I can not budge the pan! is there something I am missing?

that is supposed to have 3 60 watt bulbs

I emptied a propane tank to make a BBQ pit in the back yard and still smells of propane? how long does it take to dissipate into the air? Is it just the added chemical that makes it smell? or are there pockets of propane still in my yard a week later?

It is a 67" ID 8' long so holds close to 1500 gallons, could I make a slab 7'x7' and seal the contacted ring with silicon? There must be an easy way to do this.

I look at adds for 55 gallon barrels for 75 bucks, but you can get a culvert for 150 bucks that could hold 750 gallons with a little work. Seal one end with concrete drill a hole for a faucet and viola. Is there something I am missing?

We have Tex-Star that have produced well but our Loring has not fared so well as far as making peaches yet it is about four years old. Is it the chill requirement?

Or will I need to go back to the main supply? My house was built in 1963 in Austin Texas. The water heater that is there now is fed by a 1/2 inch line with the type of valve we had in high school science for the bunsen burner.

Prolonging tomato plants in Austin tx?

We put our tomatoes in late and the temp is pushing 100' right now the tomatoes have flowered but don't seem to be making tomatoes? should we shade them? is it too hot now ? The plants look great, five foot tall covered in blossoms, half heirlooms half hybrids Help with any advicePlease Thank you

We put our tomatoes in late and the temp is pushing 100' right now the tomatoes have flowered but don't seem to be making tomatoes? should we shade them? is it too hot now ? The plants look great, five foot tall covered in blossoms, half heirlooms half hybrids Help with any advicePlease Thank you

The Modem and router to get it back again ... then 5- 10 minutes later it does the same thing? This is with ATT DSL the cheapest version any ideas why it does this? or how I can fix it? I have tried three different routers... and have the same issues.

Then I have to restart the dsl modem and the Wifi router to get it up again. And it lasts 5-10 minutes. Any ideas why??

But I am the default login and password is not working, "admin"& "password" sometimes it states the number of letters entered is wrong... HELP

It's default login and password is "admin" & "password" but when I type it in It states it is the wrong number of letters? the model is a "RangeMAX" I thought this would be easy.... HELPPPP!

Can you give me a supplier?

I bought a screen replacement kit on EBay did all the steps but it doesn't seem to be responsive to touch? that is the slidw will not work to unlock the phone? any ideas what I might have done wrong?

It will receive but not send, Is there a board that can be replaced? what is the cheapest way to do it?