Garrett

Title says it all.

A little explanation as to why would be greatly appreciated.

Thank you!

I was recently doing my everyday work of repairing xbox 360s and I was going to bite down onto a small strip of electrical tape to tear ir and noticed something in my mouth. At first I figured it was a piece of the tape by my gums and as I went to fish it out with my tongue it pushed the chip back down. After a few seconds with a toothpick a small thin layer of my tooth fell out of my mouth. I think its the a part of the filling that was in my tooth, but Im not certain.

I have a lot of plans today and I dont want to have to have my teeth drilled again as I have serious anxiety and it drives me crazy. If i go to get it repaired will they have to drill again or can they refill it? What will happen if I wait a few days?

It doesnt hurt it just feels a little rough where the chip came from.

Any advice at all would be greatly appreciated, thanks!!

thanks!

I have a 1995 Pontiac Grand Prix SE with a .1 liter v6. SFI

Recently its been overheating a lot and the coolant has been nbacking up into the resorvoir, bubbling violently and spilling over. The heat doesnt work as well.

I recently replaced all of the cooling hoses, water pump, and thermostat.

The only thing ive noticed is that the water fitting before the heater core is a little leaky, nothing big that i know of.

The first time i replaced the pump it worked like a charm and i even got better gas mileage. I need a car to get to school and back and this isnt proving to be reliable.

What else could be causing the problem?

any help would be great!

(just replace head gaskets, heads, and all other gasets.)

thanks!

First off, I have a 1991 Oldsmobile Cutlass Supreme with a 3.1 liter V6 engine with about 168,000 miles on it. My car started to run boggy and often stalled until a point where it wouldnt start, and then it would start when cool, but run like crap.

I was told it was my crankshaft position sensor, so i went to Carquest and bought a replacement for around $30.

I went to remove the old one and ending breaking most of it and there is only about 3/4 of it left inside the block. Its a really tight fit and most of the plastic is warn at the surface down to the metal components from hours and days of drilling and pulling on screws.

It will spin innside the hole fairly easily, so i know its not impossible to remove. And i know that some of the o-ring is is still on it.

I dont know what to do, and sure cant afford to pay to get it replaced.

I had to pull the cylinder head off to make room to work.

i have to remove it by sunnday this weekend or i have to drop my car off at the junkyard, parents orders.

Any ideas would be great!

I was getting ready to remove the old one because i had people tell me that it was causing my misfires, and often running on 4 cylinders out of 6 leading to the engine not starting, but getting some occasional sparks.

The problem is that most of it broke off and is still in the block and i cant remove the oil pan without taking out the engine itself, and isnt possible at my place.

I was thinking something to dissolve the plastic and then pull it out with pliers, but nothing is working.

Its a 1991 Oldsmobile Cutlass Supreme, with a 3.1L V6.

Any help would be greatly appreciated!

thanks

So... Im a total Mac noob. WIndows is my thing...

I had Ubuntu on my iBook G3 for some time and grew tired of it, so i went to reformat the computer and install Mac OS X with the CD that came with the computer. It boots into the installer, but when it asks for an installation source all that shows up is the CD im using to install it with.

Why isnt my Hard Drive showing up? I know its good.

Any help is great!

-Garrett

I have an iBook 700mhz model with 256mb of ram and a 20GB hardDrive.

When i got it there was no operating system on it but it did have a mac os x install CD.

The cd boots up just fine when i hold down 'c' or go through the boot menu using 'option' but after the cd scratching for a few minutes and a loading cursor with the mac logo in the center of the screen, i get this error: "The installer has unexpectedly quit. (error 1)

Im no good with Mac and i cant figure this out. i tried resetting the vram or pram or whatever, but no help; same error. Ive heard a lot about a firmware update t o fix the issue, but without an os, i cant do that. any help is great; thanks!

Im new to Mac and i recently got an iBook for free.

the specs are as follows: 700Mhz CPU, 256MB ram + 128in slot, CD-Rom and so on.

Im trying to install Mac OS X "Aqua" because there is no OS on the hard drive and i want mac. But when booting up the CD i get this message: "The installer has unexpectadly quit. (error 1) Press Return to restart the computer"

Any help please!

I have a 1991 Oldsmobile Cutlass supreme, with a 3.1L V6 engine. I recently replaced the front head gasket to fix spraying coolant, and now after it running great i put coolant in it and its leaking out of the exhaust from the tail end of the car. I know its from the back head area because of the manifolds location. I have the head pulled off and the gasket looks pretty bad, but it doesnt seem to have any way of letting coolant into the engine or out of the exhaust. And from what i can see my head isnt cracked at all.

What could be the problem?

Thanks,

-Garrett

Ive been hearing some gossip about a "universal server" that can host and combine players from all platforms i.e. PC, XBOX 360, PS3. Ive done some research and cant seem to find anything. Anyone?

-Garrett

I have a 91 olds cutlass supreme and when replacing the lower intake manifold I noticed that the water fitting from the engine to the heater core was broken. The threads were still in the engine and the person that tried to get the threads from the fitting out made the hole bigger and ruined the tapping. I dont know what to do. I thought about running the line that originally went from the outlet from the hole where the Coolant temp sensor was. I dont know what to do. Help!?

Thank you!!

-Garrett

Cutlass Supreme

not cutlas suspreme. sorry!

I have a small weed eater engine and a few servos laying around. Im looking around for a 2-4 Channel radio for this build. I want to build either a plane or a small car/buggy. Anyone have any ideas or pointers here? Anyone ever tried something like this.

Any ideas are great!

Thanks in advance,

-Garrett

Does anyone know why the questions are hours old and not updating? Or is it just me?

Ive had my camcorder for a year or so now and I just want to get the hack done right. The firmware is 53.12, has anyone ever done this or is there any good guides on it. I managed to put in a rechargeable battery and the USB port, it charges via usb. I just cant get the software to work!

Any help is great!!

Thanks in advanced,

-Garrett

Me and my girlfriend have been dating almost a year now and we are ready for sex, well we have been for quite some time now. Its a long story on how we met and came together. Anyway, we have done everything we could imagine but sex. We have tried multiple times to do it but there's always something stopping us, like having to stop and put a condom on... awkward :/

But the biggest problem on hand is that I cant seem to penetrate. Im not like freakishly big or anything i just dont know whats going on. We both believe that her hymen has already been broken. We get as far as the very tip and it just doesnt go anywhere from there. I dont know why we cant have sex. It really confuses me. Any ideas? Shes not dry, I wear a condom, and her hymen is broken. Whats going on?

12 Gigs of ram and a core i7!?

anyone been there?

Almost a year ago my girlfriends mom commited suicide. It was the day after mothers day. Her mom was her best friend, she told her everything and her mom gave her the support that no one else would. Her mom was proud of her and always told her she was perfect the way she was. And her dad and brothers were never there to do that. Angela (My girlfriend) and I had visited her mom the day before mothers day to give her a gift, and say the I love you's, you know... mothers day stuff. Ever since her passing she has never been the same. She is mean, and seems very ungreatful. But today I realized that all she wanted was her mom back, and the gap to be filled where she used to be in her life. She is lost without her. Im there for her every day with all the support I can give her but I can never get her to be the same again. I miss her :/

Im not asking to cure her from her sadness, just to help her move on. I dont know what else to do. This isn't to compete for points or anything, I just really need good honest help.

Thank you inn advance,

-Garrett

My outlook on life has always been, living it day by day and not thinking about the future other than College, work, and with my girlfriend. In my health class we recently dug into the subject of death, organ donation, etc. Creepy...

But ever since than all I can ever seem to think about is that some day im going to die. It seems like the end is so near and I have so many fears about 'the end' like: Will I die alone? What if my wife dies first? Its all really hard to explain. Ive just been so depressed about it lately and I want to be "me" again. It sucks a lot. Im never happy. I look at someone poor, or having a bad life and think "their gonna die and their life is that f***** up!?

Its really bringing me down. I know that everyone dies and its normal and all of that good stuff we learn as a kid.

I dont know what to do...

thanks!

-Garrett

I have a 1991 Oldsmobile, Cutlass supreme with a 3.1 Liter F1 V6 and I was removing the upper intake manifold and there was a small black box with a thin black hose going into it and had a 3 Prong plug going into it. As I was pulling the manifold off I broke the connector for the hose. I want to know what the sensor is so I can either fix it or replace it. Is it really important? Is it expensive?

Thanks in advance,

-Garrett