Hillabee Creek Redneck

Today I purchased a 32 gig flash drive with the salesmans assurance that I could backup my pc on it.

I have tried but I keep getting prompted to insert a cd before I can procede.

Did I get bad advise or am I doing something wrong?

I have installed a 1989 1.6 Suzuki motor in my air boat and I have had some trouble with it. We had to bypass the computer and engineer a carburetor mount for it and that part works very well. I do however have recurring problems with the distributor; I would like to find one that uses the old style breaker points instead of the electronic ignition.

I can't find one online but was wondering if the distributor from the 1.3 liter might work as it is a little older and may have breaker points. Thanks Glenn

This boat has a 4 cyl Suzuki motor on it and is lots of fun to ride in, but it will not run if even a slight drizzle should fall. It is totally useless when the motor gets wet.

Is there some way I can water proof the electrical system, thanks Glenn

My wife has an old VCR tape she needs to get transferred to the CD format, how do I do this?

I've recently acquired several old books and a couple of old newspapers. I would love to know if their is any value in them. Thanks Glenn

I haven't had this problem before, but now every cd I insert gives me the same message and tells me to insert an empty cd.

I think that it is confusing the time that will be free after the burn, but why is this happening?

Thanks Glenn

I have a Dell inspiron 531 with the vista operating system. I have an out of date version of norton that I can't get deleted from my system,although I've ran their remove and reinstall tool twice.

The old icon is still on my toolbar and keeps popping up with the message that my coverage has expired .

Also I don't think that my new version has launched and thierfore not protecting my computer.

He has installed a new crankshaft position sensor and a new throttle position sensor, new plugs and wires, a new coil and nothing seems to help.

It has been checked with a scan tool and no trouble codes were present.

It is only hard to start the first time each day, after that it starts easy. The fuel pressure has also been checked, and was ok

I have a problem with java and it seems to be caused by errors,junk,and clutter, maybe even a virus or two.

I know that I'll have to purchase someones product to get this done but I want the most for my money. Can you guys help me?

Julie's camera has a locked memory card and I don't know how to unlock it

I recently changed from McAfee to Norton for my protection, now I have no sound?

I've tried to turn it on thru my control panel but can't get anywhere. I also had to change my keyboard and mouse, it's all blue tooth, any suggestions?

I had the alternator checked and it was ok, but now the car engine is stalling even with the ac turned off.

I'm now thinking it may be a relay that maybe controlls both the ac and the fuel pump, or perhaps the junction box where they are located? Thanks Glenn

My car has developed a problem, When I turn on the A/C or the defroster the engine dies as if I had turned off the ignition. I thought it may be the battery but replacing it didn't help.

I first thought the A/C was pulling too much voltage from the battery and shutting the ecm down, but the lights and other electrical loads do not effect the engine at all.

I've been told it may be the alternator but I thought a new battery would solve the problem at least for a few minutes, but it did not. The engine will run with the battery cables disconnected as long as the A/C switch is turned off, so I don't thing the alternator is the problem.

I'm in Houston Tx on work but must get home to Alabama on Thursday that's a long drive when the a/c is working and going to be much worse without it. Thanks Glenn

I had assumed that it was made by Springfield Armory here in the US but now I have noticed them listed as the importer of the gun.

I finally read an article in Guns and Ammo where I saw the reference to the importer.

I'm a little suspicious about the gun because I've never seen a product pushed by the amount of advertising as this one is.

Do any of you have this gun and is it worthy of the coverage it gets in the gun rags.

I have noticed the price of charcoal starter has gone up in price quiet a bit, so I started thinking, is there a substitute.

I would like to here from someone knowledgeable in this area thanks ,Glenn

I have a project where I must open and reshape some pockets that are cut into stone. The pockets are approx. 2"high x 4" wide and 6"deep. They were cut with a star drill and mallet back in 1910, and as so are not cut accurately enough.

I must square the top of the pockets where they are now tapered at a downward angle due to a ledge that prevented the worker from achieving the proper angle with his drill.

What I need is a pneumatic hammer and some carbide chisels that will work in a tight location.

I can't seem to find the tools that will serve my needs, Thanks Glenn

I got the hdmi cable and ran the rca cable between the digital audio jacks, and still I have no surrond sound on tv. I have it on dvd, but no response from my tv.

Am I forgetting something here, perhaps a setting on the tv, someone please help me.

I have a Philips 42" tv model (42PFL6704D) and a Philips home theatre system( HTS3372D) and I need to know if I must use a HDMI cable to make the connection between them. I have been trying to do it with old dubbing cable I had on hand but I can't get it to work.

I can purchase the cable as soon as something opens after Christmas, but I would love to enjoy it for a while today. All help appreciated, Glenn P.S. merry Christmas

I have a Millermatic 251 Mig welder, It has started running very cold although the output meter still reads as it should the heat isn't near normal.

I must turn the voltage control to 27 and the wire feed speed to 200 ipm to get the same performance I was getting from 18.5 volts and 312 ipm.

Do any of you have an idea what is causing my problem ?