Soft Talker

The doors lock and unlock with the remote door lock device but I can't lock or unlock any door with the lock switch on any of the doors? Also, the windows will not move up or down with the auto switch on any door. Also the interior lights will not go off unless the battery is disconnected. The mirror adjustments for the right and left exterior mirrors does not work. All this began at the same time. I lowered the windows for the dog and then locked the car doors, when we returned all this had happened and we came home with the windows down. I disconnected the battery to shut the interior lights off and retried the whole system after reconnecting the battery. Nothing better, still as I described above. All the fuses look OK and I do not know what else to check. We live 85 miles from the nearest dealer repair. Can you help.

When making a hard right turn there is a noise from the rear that sound like tires slipping on the pavement. When I jack up the rear and try to turn the wheel they turn easily for about 3/4 turn then it gets real hard to turn. Any ideas? Lube is fine. This seems to only happen on a right turn and not al the time??

I was looking at gold prices yesterday and I found something that I do not understand. What is meant by, "Gold prices change, falling by another Rs 25 to Rs 27700 per 10 grams. I have no idea what any of this means. What is this Rs??? I guess what I need to know also is what does Rs mean and how can I understand it related to ounce or some other system I understand/

When making a native style wooden flute, twice I have had great success until the last hole on a six hoe flute. When I try to tune the sixth hole I can get the key, or close, then it will over blow and squeak. What is causing this?? The flute is on KEY and tuned to scale until the sixth hole.

All the sudden I can't down load from youtube. Has something changed or do I have a problem with my Real Player

I finally found the spark plugs and how to get to them. Is there a distributor on this thing or is the timing and firring sequence controlled by the computer?? Is there something other than spark plugs that needs to be changed? I am from the old distributor. rotor, condenser times.

Old computer had Microsoft Works word processor, New one has Microsoft Word starter.

How can I get the works documents to open without works on the new computer?? I transferred all documents to the new computer and I can't open them??

This thing will not go into overdrive. It shifts well except for not going to overdrive. Reverse is fine, no noise and everything is smooth. Any ideas??

In the distributor there is a part called a reluctor. It is loose on the distributor shaft. It has two slots that look like a place for a key or lock to hold the reluctor in place on the shaft. Is this held secure and if so how.

I have been asked how to get the claws out four bear paws with out damaging the claws. The claws will be used for Native American necklace and other items so we do not want to damage them in any way.

When we run the washer it goes throught the initial water stage and then stops and displays "C3 see door label". The door lable is long gone. What does C3 refer to?? GE Potscrubber 2230.. Thanks for your help...

What are the tow in specs for this P.U.? I have replaced the thie rod ends and need to set the tow in. Thanks

The lights I have been buying last two years at best, most only last one season and will not work when you pull them out for the next year.

The wood is only 1 1/2 inch square. All attempts so far have ended up with the drill coming out the side before I get to the other end of the wood.

Replacing the ball joints on my 85 dodge pick up. The upper ball joint has an adjusting sleeve. What is the proper procedure for adjusting this sleeve? ball joints have already been pressed into the steering knuckle. I thought I would tighten the bottom joint nut first then adjust the sleeve down to meet the upper ball joint. right or wrong? how tight should the sleeve be? Any suggestions would be helpful. Thanks

Can I pull the intermediate axle on the left side without pulling the disconnect assembly? Any suggestions for reinstalling the axle shafts? I do not need to pull the inner axle shaft, all is OK here. The axle shaft on the right side does not seem to be a problem.

I am hooking up a 30 amp rv outlet to connect my trailer to for electric service. I have to use a 10/3 with ground wire. I have black, red, white and bare. I use the white for common, the blacke for hot. The question I have is, of the red and bare wire which one goes to the ground connection on the outlet and which one goes to ground in the outlet box and service panel. I have no problem getting it to be safe, I just do not know which one is used for ground at the plug when there are four wires and one is red, not green.. Thanks

Where can I get help setting up solar power for my shop. Electric Co wants 1900.00 to connect to grid. Can I get help in getting solar panels and related material to go solar rather than connnecting to grid. Would like to do that but I can not afford it!!

I have changed fuel filter and coolant temp sensor. When I turn the key on the fuel pump runs and then stops. I just bump the starter with the ignition key and the pump goes through the same cycle. Do this two times and then the engine will start in one revalution or two! This is when the engine is cold. If I shut down and restart, no problem. If I shut down and wait 10 - 15 minutes before starting the problem begins to re-apear.