nunmorenegative72

Mortgage Co Gave me $1500 to move after foreclosure and gave me 1099MISC Do I have to file it?

This unit is only 3.5 years old and recently the fridge has gotten very warm although the freezer is cold as ice. I cleaned the coils of the condenser from the front and rear of the fridge, clean all dust from underneath and made sure fan was turning and there is no ice buildup anywhere. everything looks and works fine except there is no air flow coming into the fridge through the damper vent on the upper left side of the fridge. I replaced the damper assembly and its still not opening. what else could be wrong.

I have a question hopefully someone can answer. There are two small blue switches next to the shift coupler and shifter. i know the one on the bottom allows for the key to be removed when in park, what is the other one on top for and what its called, because it is broken and I need to know what to order.

This unit is only 3.5 years old and recently the fridge has gotten very warm although the freezer is cold as ice. I cleaned the coils of the condenser from the front and rear of the fridge, clean all dust from underneath and made sure fan was turning and there is no ice buildup anywhere. everything looks and works fine except there is very little air flow coming into the fridge through the little vent on the upper left side of the fridge. what else could be wrong.

I replaced both elements and thermostats about a year ago and I did all the checks on the thermostats and elements and they have all checked out ok. I also drained it and checked the water pressure at both outside spickets, they both pegged the gauge all the way around which would be about 130 psi or so. i also changed the t&p valve last year twice. the problem is that i have water flowing slightly out of the t&p discharge pipe, about a gallon every other day. I set the thermostats to 140 degrees and its a little more discharge, I set it to 120 and it slows down some. any ideas you can give me would be of great help.

I have a 50 gallon electric hot water heater thats about 10 yrs old and it has been drained recently and the elements and thermostats were replaced about a year ago. the shower gets completely cold after about 10 minutes as it used stay hot for 20-30 minutes. what could be the cause of this, how do you test elements/thermostats.

I have no heat coming out of my vents. I replaced the thermostat, flushed the system, made sure it was bled properly and still no heat. The temp gauge reads between about two-three lines below 210 degrees and there is no check engine light. What else could be causing this.

I installed a brand new thermostat and coolant temp sensor on my 03 ford explorer with a 4.0 engine about 2 months ago, the P0128(low coolant temp) code is now coming on. what else could be causing this.

this explorer is all wheel drive and i rotated the tires yesterday and noticed that when you spin the front wheels they are very tight. is this normal since they go into the front differential. also about 4 months ago i had to replace both hub assemblies, i didnt have a torque wrench to torque the axle nut. using an air gun, could I have possible over torqued the nuts.it calls for 250nm or 184 lb/ft.

my washer has 4 temp settings: cold/cold, cool/cold, warm/cold and hot/cold. when I use hot/cold it switches to hot as its supposed to. when I use the other 3, the temperature of the water doesn't change and stays on cold. is the switch bad or something else.

It was working last time I used it, now it will not even open on any computer I plug it into..nothing at all. Is the flash drive bad or can I do something to fix it. It is a 32gb drive.

I have put three deck belts on my ariens 42" mower this season. I am getting ready to put my 4th belt on, what would cause the belt to break so much. Could a misaligned tensioner cause it. It calls for a 100.25" long belt, thats what I have used each time.

What was the deal with the bracelet in the box that he dropped.

I have a Kohler twin cam 18HP engine that has a Kohler oil filter on it. I went to buy one and it is $18, I can buy one for a car for like $3. I found one that fits perfectly and doesn't leak when running. My question is, will this one for the car be ok, like internally are they the same. Is the oil flow the same or is the small engine filter made differently.

I upgraded an old desktop(compaq 5002US) from a 800Mhz AMD to a 1.2GHz(A1200AMS3C) processor. However, it only shows 900mhz in the bios system info and on windows xp system info. why is this happening and can it be fixed.

I bought pc133 sdram for my old compaq desktop because it was advertised as backwards compatible with the pc100 originally in it. but this ram causes blue screen errors and even slows it down. i put the old ram back in and it works fine. is there a way to make it work, like a setting change or jumper?

Just recently I have noticed quite a bit of red insulation particles and trash on the floor around two of my vents inside the house. I went under the house this morning, and none of the pipes are off the vents and no holes anywhere I can see. Where would all this be coming from. BTW all the insulation under my house is yellow, whereas the insulation on the floor is red.

I have the 30mbps cable broadband and my xbox 360 takes about 10 minutes to download a 800mb game demo. shouldnt it download alot faster than that. i can download a 800mb file in like 30 seconds on my laptop, what could be the problem.

I have a netgear cg3000d wirelss router using charter communications 30mbps high speed internet. my question is that in the setup configurations it is set to 145mbps what would happen if i set it up to 300mbps and its now at channel 11, should i set it to auto. the internet runs fast but it doesnt seem like its as fast as i should be. i just upgraded from 15mbps speed to 30mbps speed and it seems about the same.

I have a desktop running xp with an HP P1006 Laser jet printer that I am having problems with. I have been using it for about 2 years now and all a sudden it quit printing midway through a print job. I unistalled the software and reinstalled it, still nothing. I put another brand new p1006 on the computer and reinstalled all the software with the cdrom, still nothing. I put a brand new canon printer on the computer, still nothing. I tried a brand new usb cable and power cable, still nothing. in my properties its listed a default and online and all the settings are correct. I downloaded the driver update as well. It is not printing a test page either. I am stumped anyone have any advise.