Mazda man

I have a 2005 chrysler town & country that cranks but wouldn t start. I checked for fuel and sparks and discovered that i don t have any sparks. However, if keep cranking i get sparks for a second or two then nothing.

Please note: whenever i get sparks, the engine wants to start. I replaced the crankshaft sensor, the camshaft sensor and the fuse box. I do have these codes:

- P0129 Barometric pressure out of range - low

- P0508 Air control valve sensor circuit low.

I someone could tell me how to solve this problem I d appreciate it.

Thanks!

I lost my wallet while in a trip to Colorado. I have no money or whatsoever eccept a thick gold necklace of seven links. I went to this hotel in this small town and I asked the manager if I can stay explaining my situation and offering him one link of my necklace for each day. He accepted but with one condition: I CANNOT CUT THE NECKLACE MORE THAN TWICE!

How can I give him one link every day without cutting the necklace more than twice?

Remember! I cannot pay in advance and I cannot be late for my payment..ONE LINK A DAY!

GOOD LUCK!

I never speak first and I never contradict a speaker..who am I?

I have a lot of teeth but I never bite..who am I?

I have a 2000 Chevy Astro that one morning didn't want to start. I thought I had run out of gas so I put some more but that didn't help. I checked to see if the fuel pump was making any noise and it was not so! because of the winter (snow) it set for about a year before I replaced the fuel pump then when I started it, it was running rough and has no power..not even enough power to move itself..it moves eventually and drives but so weak that even when I floor it, it cannot even reach 50 miles/Hr. the parts I replaced are: Spark plugs and wires, Mass airflow sensor, EGR valve, distributor cap and rotor, O2 sensors. PCV Valves. The tests I run are: Snap on says upstream rich that why I replaced the O2 sensors. When I try to plug the exhaust with my hand the exhaust pressure won't let me. When I push the pin in the valve on the fuel line, the fuel spits with enough pressure and the valve itself is not leaking any fuel.

Any ideas or suggestions?

Thank you very much!

I decided to start a new business. I do basically everything: Mechanic, Plumbing, Electrical, Flooring, Painting, Garage doors and carpentry. I do maintenance and repairs as well as new installations.

I set everything up and am about to print the business cards and the work order sheets but I still couldn"t find a name for my business.

All ideas are welcome and the chosen name will get the "best answer" and thanks to all of you.

I am a Moroccan citizen awaiting the American citizenship. My passport was stolen and I have to go to Morocco for a month with my American citizen 11 years old daughter (she has an American passport). I got a travel permit (laissez-passer) from my consulate to enter Morocco without passport but I am worried that I won't get my passport on time to re-enter the U.S. Is there a permit of some kind I could get so I can come back in case it takes longer than they say? My tickets are not refundable or transferable and I cannot change the dates.

I recently sustained an eye injury at work. I've had two surgeries thus far to fix the damage caused by the foreign body. Now the healing process is underway and will take time. If all goes well, I'll be fitted with a hard contact lens to cover the corneal defect caused by the injury. If things don't heal well, I will need corneal transplant. Only time will tell at this point. Worker's compensation is paying my medical bills and giving me a weekly check for loss of wages. My questions have to do with long-term outcomes and expectations.

1. Is there a schedule whereby I can determine how much my state will pay out for loss of wages , work placement, vocational rehabilitation, or even permanent partial disability if my vision is not restored? I would also like to know about how long it will take for my eye to heal after all these interventions?

2. In legal terms, how long before I've reached what's called the "MMI" maximum medical improvement?

Bottom line, I would like to get a better sense of the minimum and maximum of what the work comp will pay in the event my vision is lost forever.

Thank you all and god bless

I posted the following question few days ago but didn't get a satisfying answer:

I was installing a snow plow and needed to hammer a bolt through an opening. I grabbed my deadblow hammer (rubber on one end, brass on the other) for the job. Hitting with brass end, a chip from the hammer flew into my eye. Immeditate pain. I stayed at work to complete my shift and went home. Pain was worsening, so my wife took me to the ER. It was determined that the metal shard had torn through the cornea, iris, pupil, and was embedded between the lens and retina. Surgery was performed to stitch together the laceration where metal penetrated the eye to prevent infection. Antibiotics were injected into the eye as well. A second surgery is planned to remove the metal shard, replace the lens with a synthetic one, and remove the cataract that had formed immediately after the incident. The status of my vision at this time remains unknown. Regardless, a scar will remain, the effect of which on my vision will only be known with time. I have been ordered to remain off work for one week, and my ability to work effectively in the future is yet another unknown.

After all of this, I can’t help but think, should the hammer have chipped?

Moreover, on the hammer itself it states “wear safety goggles.” Do you guys wear safety goggles when you want to hammer something?

I have used hammers all my life. I feel like I was tricked. I would like to hear from you, to know for sure if this is just a stupid mistake on my part, or if I should take things further, so at least no one else gets hurt like this. I believe that this hammer should have never crossed the border from China.

The warning to wear goggles was written orange on orange. Secondly, I noticed it only when I examined the hammer closely after the accident.

I had the second surgery Monday. It lasted 2Hrs instead of 1/2 an Hour. The Doctor was surprised to find out that the piece of brass was as big as a fingernail...The intrusion had destroyed the eye and the artificial lens could not be placed where it was supposed to go. A transplant will be necessary for a recovery.

I said I feel like I was tricked because I have used hammers in my life and I have never thought that this one would chip on me. A hammer shouldn't chip.

Thank you all.

I posted the following question few days ago but didn't get a satisfying answer:

I was installing a snow plow and needed to hammer a bolt through an opening. I grabbed my deadblow hammer (rubber on one end, brass on the other) for the job. Hitting with brass end, a chip from the hammer flew into my eye. Immeditate pain. I stayed at work to complete my shift and went home. Pain was worsening, so my wife took me to the ER. It was determined that the metal shard had torn through the cornea, iris, pupil, and was embedded between the lens and retina. Surgery was performed to stitch together the laceration where metal penetrated the eye to prevent infection. Antibiotics were injected into the eye as well. A second surgery is planned to remove the metal shard, replace the lens with a synthetic one, and remove the cataract that had formed immediately after the incident. The status of my vision at this time remains unknown. Regardless, a scar will remain, the effect of which on my vision will only be known with time. I have been ordered to remain off work for one week, and my ability to work effectively in the future is yet another unknown.

After all of this, I can’t help but think, should the hammer have chipped?

Moreover, on the hammer itself it states “wear safety goggles.” Do you guys wear safety goggles when you want to hammer something?

I have used hammers all my life. I feel like I was tricked. I would like to hear from you, to know for sure if this is just a stupid mistake on my part, or if I should take things further, so at least no one else gets hurt like this. I believe that this hammer should have never crossed the border from China.

The warning to wear goggles was written orange on orange. Secondly, I noticed it only when I examined the hammer closely after the accident.

I had the second surgery Monday. It lasted 2Hrs instead of 1/2 an Hour. The Doctor was surprised to find out that the piece of brass was as big as a fingernail...The intrusion had destroyed the eye and the artificial lens could not be placed where it was supposed to go. A transplant will be necessary for a recovery.

I said I feel like I was tricked because I have used hammers in my life and I have never thought that this one would chip on me. A hammer shouldn't chip.

Thank you all.

I was installing a snow plow and needed to hammer a bolt through an opening. I grabbed my deadblow hammer (rubber on one end, brass on the other) for the job. Hitting with brass end, a chip from the hammer flew into my eye. Immeditate pain. I stayed at work to complete my shift and went home. Pain was worsening, so my wife took me to the ER. It was determined that the metal shard had torn through the cornea, iris, pupil, and was embedded between the lens and retina. Surgery was performed to stitch together the laceration where metal penetrated the eye to prevent infection. Antibiotics were injected into the eye as well. A second surgery is planned to remove the metal shard, replace the lens with a synthetic one, and remove the cataract that had formed immediately after the incident. The status of my vision at this time remains unknown. Regardless, a scar will remain, the effect of which on my vision will only be known with time. I have been ordered to remain off work for one week, and my ability to work effectively in the future is yet another unknown.

After all of this, I can’t help but think, should the hammer have chipped?

Moreover, on the hammer itself it states “wear safety goggles.” Do you guys wear safety goggles when you want to hammer something?

I have used hammers all my life. I feel like I was tricked. I would like to hear from you, to know for sure if this is just a stupid mistake on my part, or if I should take things further, so at least no one else gets hurt like this. I believe that this hammer should have never crossed the border from China.

Thank you all

The differential is making a grinding noise. The plug is stripped I couldn’t turn it, so I decided to replace the cover with one that has a plug on it. There are two kinds of differential: 8.5 and 8.625 ring gear. The cover is so rusty…there are no visible numbers, and I couldn’t find the service tag.

I’m trying to figure out which differential I have so I can order the cover for it. All I know is that I have 3.73 gears ratio and 10 bolt cover. Does anyone know the ring gear specs or where to find them?

5.0 L, VIN M

Thank you all.

I started working part-time for a father and a son as a cook in a restaurant few months ago after a long break because of my disability. The manager (the son) pushed me against the wall few times and called me all names because I asked him to pay me. I left work thinking never go back again and he kept sending me text messages saying that he was treating me like that because of my disability (I saved all messages). He sent me a letter few days later saying that I was not welcome at the restaurant. Same day I received the letter, I received another text message saying that his father wants me back. I went back because his father is a good friend and very nice person. I worked the first week and got paid 2 days late and $100 less. I was also asked to work full time for $10/Hr. I have worked 301 hours this month (7days/week 9 to 13 hrs/day), but he gave me only $200 3 times, and when I asked him to pay me, he said that I was on a salary of $200/week, that he gave me $200 5 times not 3, that I was missed up in the head and I don’t remember everything, and that I don’t deserve the $10/hr while a dishwasher and 2 waitresses make $7/hr. I keep my log up to date and my detailed records support my claim. He manages every penny and he is claiming that the restaurant is not making any money. His father is the chef and the owner but has no word to say as the son is a trustee. The father works every day 16 to 18 hours but never got paid. I would like to give the son a lesson without hurting the father. Can I take him to court? Or should I contact the Social Security Administration?

What should I do?

Thank you all very much!

I was pulled over for no reason, and the officer refused to take my blood/urine sample, took my license plates, cut the corner of my driver's license, and impounded the vehicle.

My lawyer told me that he can win the case, and that I have only 8 days before I lose my license permanently. He asked $2000 for the criminal charges which I borrowed, but he wants another $1500 to get my revoked license back. Is there any way I can do it by myself if I pay the $325.00 fee? I live in Minnesota.

Thanks everyone.

I was in a trip very far from home, and I lost my wallet with everything in it. I stopped at this hotel and asked the manager if I can stay for few days until I get my documents sent to me. I offered him my gold necklace which contains seven links. He allowed me to stay seven days, but wants me to pay him for each day one link, and I have to pay one day at the time without cutting the necklace more than twice...how can I do it?

Thanks.

Please, I am very familiar with the internet translators, and I don't trust them at all.

This word is only used in a plural form, but in singular, would it be "un gent" or "une gent" and why?

Thank you.

Some well-known blowhards in the world of talk radio and Faux News have actually used the words, "I want Obama to fail." These are the same "patriots" who gave GW Bush a pass on everything he did, in the name of patriotism and the American way. How does one explain this contradictory, hypocritical viewpoint?

I am neither Republican nor Democrat. As Obama said himself, political party is not important, only our Americanness.