duane w

engine light is always on. 136000 miles. changed out the top o2 sensor and it didn't fix it. have unplugged the battery for a day. didn't work. reset it 3 times worked for 3 miles and service light back on. this is what the code read i believe. can i unhook it at the computer or something to check the plug? anyone know which exact plug it would be? suggestions?

it still has the direction control as well as temperature control. relay not stuck in on position. is it the resistor? I hate to spend 80 bucks to guess. Is it the control head whatever that is? how can you tell? If you don't know don't waste people's time please.

how do you unhook the slave cylinder line from the manual transmission? i can see a very small bolt through the access cover beside it but it is way up inside and likely not it.

I have a kid very allergic to cats and dogs and the like. I have 2 furnaces. Would a real good furnace filter help her allergy reactions to go down and if so what is a less expensive good one to get? Is the thick 3 inch paper style the one to go with or electronic type?

I have a kid very allergic to cats and dogs and the like. I have 2 furnaces. Would a real good furnace filter help her allergy reactions to go down and if so what is a less expensive good one to get? Is the thick 3 inch paper style the one to go with or electronic type?

can't find a fill dip tube is there another place to look?

Epoxy used on floor as a design top swirl. We have it a bit too thick a swirl and ran out early. how can I not buy the 2 gallons just to get a quarts worth? Could i use a oil base floor paint similarly to finish it at least in looks or will it peel off? Can you buy smaller volumes of the 2 part epoxy for a concrete floor?

A stupid answer is no answer people. Read the question.

Worked fine when last used now it won't pop on. I have tried tightening it a bit and charging up the battery well. Any ideas. I assume the 2 wires are just 12 v dc in and out. is that right? Haven't check them yet.

i have a white fiberglass pool. water is spotless all the way to the bottom. usually i can dump some stain away and it goes away. recently i did it and it got a worse brown looking stain than before. no i didn't add well water. is there a simple easy fix or will metal out do it. what works cheap? ph and alkili is fine. clorine maybe a bit low by the way. thanks

water is beginning to turn green and do have fish in it. What can i use. copper sulfate perhaps or is something a bit simpler out there and where to get it.

want to build a fire pit

I have 4 of them. have cleaned the filter etc. Do they maybe need recharged or fans replaced? what do you suppose they would charge?

we want a stained plain concrete floor look. the floor does need a bunch of patches done. skim coat probably won't stick because of the black old glue. will like a ardex product stick and last as a finish coat? how do i achieve this surface prep?

Not the engine but the boot and drive shaft area immediately behind the engine. The dealer can't find it out yet. It uses same oil as engine the manufacturer says.

Question about freeze plugs on side of engine behind carb. 2 of these are kicked out till they leak . I got it this way. Have them exposed now do you drive them back in and chisel and pean them in or remove and get new or what? If I tap them back in will they leak or how do you seal them in? It is in an old boat 1974 era

I have a used shell hooked up to my pool pump. It needs a air pump to make the bubbles and such. It is about 6 foot square . Not the biggest but probably a 6 man in size. No labels. There are 13 large jets and numerous other air ports. Not the super fancy jetted one I'm sure. Anyhow I see some dealers saying 1 1/2 pvc pipe is only rated for 1 hp air pumps. Is a 1 1/2 Hp pump going to be over kill? 110 volts preferred. It has a 1 1/2 air manifold thingy with like 10 1/2 inch take offs to start with then goes all over the place with more manifolds on the manual controls. I had to use 1 -- 1 inch pvc straight connector inside of it to repair a break but it is only 1 1/2 inches long.

Heat control doesn't control anything . constant hot. Can hear a little motor when turning temperature selector back and forth.

Fan only has a high speed. Is it a regulator? If so where is it located at?

My roses have small yellow leaves What is wrong? I fertilized 1 mo. ago with rose fertilizer

I have a 5 ton jack that needs fluid. I've tried to pour it in the plug but that didn't work. Seems to have a bally looking valve at the bottom maybe.